The timing and principle of coffee flower drawing | the width of the cup mouth and the angle of injection have an impact!

Professional coffee knowledge exchange More coffee bean information Please pay attention to coffee workshop (Weixin Official Accounts cafe_style)

Coffee surface beautiful pull flower, is the use of milk, milk foam to make, coffee pull flower has its difficulty and skills, pull flower, to consider different coffee cup size and adjust the distance poured, pour, different injection angle, may also affect coffee pull flower outline pattern clarity, coffee pull flower is skill learning, art, in learning pull flower before, first understand coffee pull flower timing and principle bar!

The right time to pull flowers.

The so-called timing of flower drawing must depend on the complexity and size of the figure you want to pull. If you want to draw a larger and more complex figure, you need a little more drawing space. It is suggested that when the fusion is five minutes full, put the mouth of the flower cup close to the surface of the coffee to make the flower shape.

However, the timing when the beak can get close to the surface is related to the cup type used. Generally speaking, high and narrow cup shapes (such as mugs, take-out cups, etc.) will require a relatively high fusion ratio, and it is recommended to merge to six or seven points full. otherwise, when it comes to flower drawing, it will be too far away from the surface of the coffee because the steel cup mouth is too far away from the surface of the coffee. And the use of wide-mouth short cup, because of the wide mouth, the steel cup can easily shorten the distance between coffee and coffee, and because of this, the use of wide cup can start to draw flowers earlier, if you want to draw exquisite graphics, wide-mouth cup will be a good choice!

The difference between the level of injection

The technique of flower drawing is just the opposite of the fusion technique. The milk foam injected from high to low during fusion increases the downward impact of the foam, so that the foam will not float but is brought down into the Crema to combine with coffee.

If the milk is injected from a lower height, it can slow down the downward force of the foam, let the lighter foam float, and form a clear white line on the surface of the coffee, so when pulling flowers, the mouth of the steel cup should be lowered to the height closest to the surface of the coffee.

Thickness and angle of milk column

The relationship between the extension force and the penetration force and the angle should be injected with a small milk column during fusion. When the angle is closer to the vertical, the downward penetration force can reach the maximum. On the contrary, if the milk bubble is injected with a thicker milk bubble, the angle between the milk column and the liquid surface is reduced, and the slower the penetration force increases, the easier it is for the foam to expand and form on the surface.

So if you want to make a clean, contrasting flower, you have to hold the relative position between the mouth of the steel cup and the coffee.

When pulling flowers, it is necessary to lower the steel cup so that the amount of milk foam is thickened and stacked on the noodles. "

When fused, it is high and thin.

When drawing flowers, it is low and thick.

Changes in points, lines, and surfaces

Drawing flowers starts with a "dot", and the original shape of the flower can be regarded as a dot. When we continue to inject milk foam in place, the foam will be stacked layer by layer, and then the dot gradually expands into a large circle.

And if we keep moving the injection path to both sides and backward while injecting the foam, the dots will be strung together in a continuous line.

Pull flower is a surface composed of points and lines, combined with different pouring techniques, you can create a variety of graphics.

Stacked points and moving points.

By mastering the timing and gestures of pulling flowers, you can stack patterns with milk bubbles.

Drawing basic figure ─ double-layer tulips steps to disassemble

Two circles, strung into flowers

When you are proficient in heart-shaped flower drawing, you can begin to practice multi-level tulip flower drawing, stack one circle after another on the Crema with milk foam, and then use the closing technique to string the circles together.

1. After the fusion is completed, tilt the cup to find the starting point of the pattern. Pull the cup mouth as close as possible to the surface of the Crema, pull flowers.

2. When the white foam is stacked, it is necessary to maintain a stable flow rate, so that the foam range will become larger.

3. Until the white circle is really formed, lift the steel cup, put away the foam, and then take a step back from the mouth of the steel cup.

4. the second injection, push forward with the same amount and height of milk foam, so that the second circle is formed behind the previous circle.

At the same time, remember that as the capacity increases, the cup should also be corrected. Seize the opportunity to finish until the cup is getting full. At the end, shrink the milk column, lift the steel cup slightly, and then move forward.

6. Maintain the same inclination of the steel cup and continue to move forward and finish.

7. Maintain the penetrating force of the milk column and keep pulling to the bottom of the first circle.

Maintain the penetrating force of the milk column and continue to pull to the bottom of the first circle.

9, pull to the appropriate tip to form, then put away the foam.

10. Double tulips are finished.

Tips

Each time after forming a circle, the injected circle is made to glide forward by merging a uniform and liquid Crema surface, and each time a solid white circle is stacked to grasp the timing of the emergence of milk bubbles. For the first challenge, it is recommended to start with two layers of tulips.

Part of the content source: "Coffee flower drawing technology collection"

END