How to adjust the video thickness of the rough dial of the bean grinder
How to adjust the video thickness of the rough dial of the bean grinder
The specific steps for adjusting the bean grinder are as follows:
1. Start to adjust the grinding parameters after determining the adjustment direction (coarse or fine). Make sure there are enough coffee beans in the warehouse, and make sure that the valve between the warehouse and the grinding knife is opened so that the coffee beans can fall smoothly into the grinding area.
two。 Start the bean grinder, run for 10 seconds, and throw away the ground coffee powder (these are unadjusted coffee powder)
3. Make a cup of coffee to ensure the accuracy of the steps of serving, smoothing and crushing.
4. Test the quality and extraction rate of coffee
5. Repeat the above steps until the quality of the coffee is perfect.
About adjusting the electronic bean grinder
When adjusting the electronic bean grinder, you need to consider two variables: the amount of powder and the degree of grinding. Adjust any variable, and the latter will change accordingly. The ordinary electronic bean grinder adjusts the grinding and pulverizing time of the bean grinder according to the preset amount of powder (please note that the amount of powder is adjusted by the mill based on time rather than weight). If the quality of the coffee is not perfect, the first thing you need to do is to determine whether there is a problem with the amount of powder or the degree of grinding. In general, the distance between the correct weight, flattened and powdered pressed powder and the outlet should be 5-6 mm. If the height of pressed powder is too high or too low, you need to adjust the powder output of the bean grinder (that is, grinding and pulverizing time). When adjusting the amount of powder, the range of each adjustment should be between 0.2 and 0.3 seconds, and you need to re-test the quality of the coffee after each adjustment. If the pressed pressed powder is highly qualified, but the extraction time of the coffee is still too fast or too slow, then you need to adjust the grinding degree of the coffee. When adjusting the degree of grinding, make sure that the range of each adjustment does not exceed 3 mm. After each adjustment, throw away the first 2-3 pulverized by the bean grinder to ensure that the grinding degree of the coffee powder used during the test is fully adjusted. After testing, continue to adjust the grinding parameters according to the results.
What is the scale of the XX bean grinder?
The premise is that only your bean grinder, and can not change the beans, the amount of powder does not change, the strength of the powder can not be changed.
Remember a little trick: when you find the right powder thickness, twist it with your hand from time to time, pinch it, feel it with your body and write it down as much as possible, so that even if you change the bean grinder, you don't have to rely solely on the scale to judge. If you pinch it with your hand, it will be significantly thicker, which can greatly improve your efficiency.
- Prev
How to get the extraction part of Delong coffee machine S3200 stuck at the bottom?
Delong coffee machine S3200 extraction part stuck in the bottom how to go up 1 Delong 2200, Delong 3000B, Delong 3200, Delong 4000, Delong 4200 series coffee machine, the warning light is always on and the machine does not work. After entering the test mode, start the motor, the motor has a slight action, but does not work. After inspection, the bridge stack (rectifier bridge) on the circuit board is damaged and the bridge pile is replaced.
- Next
Instruction manual for descaling steps of Delong coffee machine
Instructions for descaling steps of Delon coffee machine the red light under the Delong coffee machine cleaning key (descaling lamp) keeps flashing, it should be descaling, in the standby state, add Delong coffee machine cleaning agent to the water tank according to the instructions, add 7 minutes to the water, then press the descaling button for a long time, wait for the above row of lights to flash, turn on the steam knob, and then the coffee machine will remove the dirt automatically (in the steam bar).
Related
- What is the Philharmonic pressure? How to use Philharmonic pressure to make delicious coffee
- Why does a hand grinder have more fine powder than an electric grinder?
- In addition to the hot mom, what is the difference between the versions of EK43 | ditting and Mahdi ek43?
- What kind of equipment do you need to make coffee by hand? Introduction to novice starter cooking equipment tools
- Espresso needs to be ground how thick and thin scale entry Italian Coffee Machine Bean Grinder investigation and Grinding course
- How much does it cost to open a small private cafe? How much does it cost to learn coffee? How to operate it?
- The difference between the flavor characteristics of hand-brewed coffee and coffee maker is hand-brewed coffee really better than coffee maker? Can I use a coffee machine to make coffee beans by hand?
- The difference between 01 and 02 of hario v60 filter cup what is the difference between 01 and 02 filter cup opening and cooking flavor
- What's the difference between the smart cup and the French kettle? Which is better, the French kettle or the Smart Cup?
- What's the difference between a smart cup and a V60 filter cup? The difference between the taste of smart cup and hand-brewed coffee