Coffee pull flower milk, how much concentration of fusion is very poor to the standard of milk
Coffee pull flower milk, how much concentration of fusion is very poor to the standard of milk
1, wet cappuccino milk foam is 6%, 7% full; (this milk bubble to make leaves and other lines require more pattern is very good-looking, at the same time, this foam can also be used to do latte) 2, dry cappuccino milk foam is full; 3, half cappuccino milk foam is 80% full; I prefer 90% milk foam. This foam is great for heart, apple and tulip patterns. In fact, what we usually use most is this kind of milk foam, which is used to make the cappuccino that is common in our daily work. Tip: practice now. I want to hit a jar full of 70% milk foam, never 90% full. Let's do it!
Several misunderstandings of milk foam
For milk foam, there are several misunderstandings that we need to understand, so that we can better understand milk foam. The first misunderstanding: the use of shaking up and down to pull the vat to remove the rough foam on the surface. This is a very good method, but many friends have a strong dependence on this method, their own milk foam did not play well, do not summarize why they did not play well, but use this means to make up for it. In the long run, there will be dependence. Here I must say that if we only rely on this way to get rid of the coarse foam, there is no way to improve the foam technology, nor can we practice the advanced skills of pulling flowers. The second misunderstanding: scoop off the coarse foam with a spoon. This method is what I reject most. Although some contestants use some methods in the competition, I think this is because their milk foam technology does not pass, the surface is too thick to shake off, can only scoop. For those who use similar methods to deal with milk bubbles, be sure to strengthen your steam control technology in milk foam.
The third misunderstanding: after beating up the foam, put it aside for a while. This method is very annoying, which is a form of expression that the milk foam technology has not been introduced yet. This will aggravate the delamination of milk bubbles, and the integration of hot milk and foam can not be completed late. if you do not pay attention to it, it will become milk and foam. The whole cup of coffee doesn't balance the taste. The fourth misunderstanding: the two jars will fall in a very high position, the original purpose is to merge, but to arouse more coarse bubbles.
The fifth misunderstanding: the milk foam is not good, blame the steam. The author believes that the steam pressure of the coffee machine (that is, boiler pressure) is relatively easy to grasp in 0.8BAR, this pressure is very long, and it is easy to understand the principle of milk foaming, but it takes about 13 seconds to make a cup of milk foam, ah, not as fast as the pressure. If the air pressure is 1. 0 or 1.1BAR, the way and method of bubbling will change, but the principle is the same. (at this point, it is necessary to rule out the phenomenon of "vomiting" caused by impure steam, and the flower jar is also shaking violently. If this happens, please empty the steam and try to heat it fully again.) Fourth, the solution that milk foam can not be injected into espresso smoothly.
We often make cappuccino coffee, there will be milk foam can not be smoothly injected into espresso, this is why? The first is that the milk foam is 80% to 90% full, which can be solved by 10% less than dry. The second is that the crema surface of the espresso is too shallow from the bottom of the cup, causing the foam to float on the crema as soon as the foam is injected. Solution: tilt the cup as much as possible to increase the depth of the surface and bottom of the crema meter. When injecting, inject it to the deepest point. The third is that the foam is close to the cup when it is injected into espresso, so that the foam does not penetrate crema enough. Solution: 10-15cm higher than the cup mouth to inject milk foam, increase the acceleration of foam injection into crema, so that it can smoothly penetrate crema. The fourth is to solve the problem by means of integration. If the foam is still white on the crema when it is injected (for a small amount, the surface is about 1 beat 3), then immediately reduce the amount of foam injected, make a circle in the cup, and then lift the flower jar up, you can flush the whitened one under the crema.
Fifth, when you pull flowers with seven-point full or six-point full milk foam, the crema will be washed away without increasing the flow. Solution: reduce the foam flow, slowly circle the entire crema until the fusion is in place and start to blossom. The sixth is the pull flower, according to the pattern you like, and the degree of milk fusion to choose the pattern you need. I personally think that the thickness of the milk foam of each kind of flower is different, so when you decide what pattern to pull, you have to decide the thickness of the milk bubble. If the pattern is too much, it will affect the taste of the coffee. Seventh, do not hesitate when pulling flowers. When you pick up the flower jar, decide the shape you need. Do not think about this pattern for a while and then think about that pattern. This will cause you to pull nothing well in the end, and the technique is also very important. When milk and coffee are mixed to 6-7 minutes, you can start to blossom. When it starts to blossom, it begins to blossom a little further back in the center of the coffee cup, and when it starts to bloom, the current increases a little bit so that it can show the pattern better, and then shake the vat evenly around to 8-9 minutes full. When shaking, the action is not too big, when the flower is almost full, go forward slightly and slowly inject milk, and then raise the water flow to close so that you can get a similar heart-shaped pattern.
- Prev
Skills in the process of making a tutorial on Common problems in Coffee drawing
Coffee drawing frequently asked questions tutorial making process skills the second category: line graphics in the shape of animals and plants. The amount of milk, foam and espresso needs to be combined according to the barista's skills, and beginners usually start to shake after one-third is full, because beginners can't control the flow rate very well. If the barista has been able to control the flow rate well without requiring complexity
- Next
Italian espresso extraction time golden ratio coffee machine what is the normal flow rate
Espresso extraction time Golden ratio Coffee Machine normal flow rate what is the normal flow rate of the espresso machine? the espresso machine is roughly divided into shock type and rotary type, which is compact in size and low in cost. It is mostly used in domestic machines, such as XX coffee machine, pump pressure 15bar or pump pressure 19bar, which means that the pump pressure peak can reach 15bar or 19bar, but it is not stable at a certain value.
Related
- What is the meaning of lactic acid fermentation with coffee bean treatment?
- How to judge the state of foam by sound?
- How does the latte pull out the unicorn pattern? Come to get for a little trick to improve the flower pull!
- Will flower pulling affect the taste of the latte?
- Do you know the history of coffee?
- The difference between honey treatment and sun washing what is raisin honey treatment?
- What kind of milk can a novice use to make coffee foam to keep the foam longer? The correct method and skills of milking tutorial sharing
- Why do washed coffee beans taste sour? Flavor characteristics of washed Coffee
- Introduction to the skill of how to practice the size and height of water injection around the circle of hand-brewed coffee
- How do beginners practice coffee flower drawing from scratch?