Coffee review

How to make milk foam Delon coffee machine how to make milk foam

Published: 2024-11-03 Author: World Gafei
Last Updated: 2024/11/03, The first step: first do fast low hit, hit until there is obvious resistance and continuous feeling; then do medium hit, also hit obvious resistance and continuous feeling; finally do high hit, hit as a whole have resistance and continuous feeling. Tip: pay attention to the height of the twitch. Step 2: repeat the first step. In this way, the process of manual milking is completed. If you want your milk foam not to be too thick, to have a certain sense of mobility, just

The first step: first do fast low hit, hit until there is obvious resistance and continuous feeling; then do medium hit, also hit obvious resistance and continuous feeling; finally do high hit, hit as a whole have resistance and continuous feeling. Tip: pay attention to the height of the twitch.

Step 2: repeat the first step. In this way, the process of manual milking is completed. If you want your foam not to be too thick, to have a certain sense of flow, just take the first step. Pulling out the piston vertically after foam is helpful to drive out a lot of coarse bubbles. (since the picture has not been downloaded, we do not know the specific samples of the author's low, medium and high hits.)

Production of hand-made hot milk foam

Heat the milk to a temperature that is hot (60 to 70 degrees) but can be held. What kind of heating method is used is not important, the key is to reach this temperature (why this temperature should be reached will be discussed later).

Production of manual cold milk bubbles

Cold milk foam is the milk foam produced by pouring fully refrigerated milk directly into a manual milking machine and using a manual milking machine. This kind of milk foam is widely used on iced coffee and has a good effect. However, the author occasionally adds it to hot coffee and obtains the different performance of cold and hot effects in a cup of coffee, which is worth a try.

The temperature of milking

The lower the starting temperature of the foam, the longer it can be operated, and of course, the more delicate it can be, which is one of the reasons why milk needs to be refrigerated. Milk foam is usually the best to do flower drawing when heated to more than 60 degrees. But we use a manual milking machine. The heat will be lost. Heat it to about 70 degrees (don't go any higher, the foam will get thicker if you get higher). The end temperature of the milk is fixed (do not exceed 65 degrees).

The amount of milk

The amount of milk added is about 2 pound 5 is enough, do not hit the highest when milking, keep the speed of the state to hit more than ten times is enough, more and more will be more and more dry. Then use a spoon to scrape off the upper layer of about 2-3cm of coarse milk foam and pull it against the flower cup several times. After pulling, tap a few times on the table, then foam in the cup, shaking the cup clockwise or counterclockwise until it is poured into the coffee. Because once you stop, it will be divided into upper and lower levels. The common problem of hand-beating milk foam is that it is relatively dry, and milk and foam are separated.

Third, how to use machine steam pipe to make milk foam

1. Preparation before milking

Understand the correct operation process of the coffee machine steam system, understand the purpose of the empty steam pipe before and after foam, and understand the importance of towels and easy cleaning in coffee making. Learn how to use the sprinkler to touch the milk noodles, the location and depth of the selected points.

2. Two temperature problems

One is the starting and ending temperature of foaming, and the other is the temperature at which the milk foam is made. These two temperatures are very important for beginners, which is directly related to the mastery of the principle of foam. First of all, when it comes to foaming, the milk is cold at first (preferably refrigerated at 5 ℃), which can prolong the foaming time so that it can be fully foamed and delicate, and then open the steam valve to foam the milk. When foaming is consistent with our body temperature (feel neither hot nor cold), the foaming is cut off.

Next, let's talk about the temperature at the end of milking. I just want to talk about what the temperature feels like on the hand. When we feel this temperature with our hands (in continuous heating), it is hot, but we can stand it for two or three seconds; as soon as we feel warm, we stop heating (the back end of the heating feels very hot on the hand, but it can hold it).

0