Introduction to video teaching for beginners in steam manual espresso machine
In the early days of using the espresso machine, Lao Yang mainly used this method, but he didn't master it well enough. The following production method is collated from the data collected on the Internet, but Lao Yang himself generally uses method two: use a double-layer milk bubble cup to make milk foam.
1. Do not put the steam pipe into the milk, because there may be some condensed water vapor in the steam pipe, so you need to put it for a while before preparing to foam to drain the excess water from the pipe.
2. Beginners can insert the thermometer into the container, then insert the steam pipe obliquely into the milk, and then turn on the steam switch. This thermometer is also used to control the temperature of milk when heating milk in the latter two ways, and it is also a tool that beginners should prepare.
3. The steam pipe is tilted and inserted into the milk pot. The generally recommended angle is that the steam pipe is at an angle of 60 degrees with the horizontal surface of the milk.
4. Slowly adjust the position of the steam nozzle to a little bit from the surface of the milk, but never above the liquid level, or the milk will be spilled everywhere. When the position is correct, a steady "hiss" sound will be heard, and the milk level will begin to rotate. If the steam pipe is scaled in the wrong position, it will be very loud or almost silent, and the milk surface may be bubbling continuously.
5. After the milk foam has been continuously dense, bury the steam pipe a little deeper and let the steam continue to heat the milk. When the temperature reaches 60 ~ 65 degrees and your hands feel slightly hot, you can turn off the steam switch. Foaming for too long will coagulate the milk and change its taste. Milk should not be too thick, because if it is too thick, it will not mix well with coffee. The milk should look like you're pouring yogurt.
6. Wipe the milk attached to the steam pipe with a wet dishcloth, and at the same time release the steam to spray the remaining milk out with the steam, so as not to block the steam pipe after the milk dries.
Three methods of making coffee milk foam
The method of double-layer milk bubble cup
1. Prepare the milk (also whole milk) and heat the milk to 60 ~ 70 degrees. Milk can be directly placed in a milk bubble to be processed on a gas stove or induction cooker, or it can be heated in a porcelain cup or glass in a microwave oven. If you use the microwave oven, because you want to pour into the bubble machine, it will absorb a certain temperature, and the heating temperature should be slightly higher. But no higher than 75 degrees.
2. While brewing coffee, the skill of making milk foam is to put a towel under the foam machine, press the lid with your left hand, hold the ball with your right hand, and twitch quickly up and down, with a small range and fast speed at the beginning. When the handle is heavy, you can stop twitching, and then put the whole bubble pier a few times, so that the milk in the foam will be thrown to the bottom of the cup, the cushion towel can play a cushioning role, and finally remove the filter, also use a coffee spoon to scrape off a few bubbles from the upper layer, is the perfect bubble.
Three methods of making coffee milk foam
The method of hand-held electric foaming machine
1. Prepare the milk (also whole milk) and heat the milk to 60 ~ 70 degrees.
2. Turn on the switch of the hand-held electric foaming machine and put the mixing head into the milk and stir continuously. Stir the pier for a few times and eliminate some coarse bubbles.
- Prev
Introduction to the flavor description of Maraka Dura hand-ground coffee with sour fragrance
Antigua coffee is popular with most coffee lovers only because of its distinctive aroma. Because it is planted in the hills of volcanoes, it can retain its own characteristics more than Costa Rica, the main reason is that it has more geographical and climatic advantages than Costa Rica. Guatemala is located in the tropics, but because of its high altitude, Qi
- Next
The principle of making Coffee by hand Pot introduction to the use of hand-ground Coffee
Put the filter paper into the filter bowl, add a small amount of water, so that there is no air bubble between the filter paper and the filter bowl; grind the coffee powder and load it evenly (this process is called cloth powder, and some people think that the uplift in the middle of the powder pile can make better coffee. On the other hand, some people think that a hole should be dug in the middle of the powder pile, which depends on personal understanding.) slowly pour hot water of about 90 degrees into the coffee powder, and the amount of water should be controlled at just the right amount.
Related
- Beginners will see the "Coffee pull flower" guide!
- What is the difference between ice blog purified milk and ordinary milk coffee?
- Why is the Philippines the largest producer of crops in Liberia?
- For coffee extraction, should the fine powder be retained?
- How does extracted espresso fill pressed powder? How much strength does it take to press the powder?
- How to make jasmine cold extract coffee? Is the jasmine + latte good?
- Will this little toy really make the coffee taste better? How does Lily Drip affect coffee extraction?
- Will the action of slapping the filter cup also affect coffee extraction?
- What's the difference between powder-to-water ratio and powder-to-liquid ratio?
- What is the Ethiopian local species? What does it have to do with Heirloom native species?